MAIN MENU

CATALOG INDEX
BY ALPHABETICAL
ORDER

CATALOG INDEX
BY DEPARTMENT

For more info:
jsi@jsits.com

 

 

Test for Assessment of Surface Cleanliness & CTR

Dust on Steel Assessment Equipment

ISO 8502-3

  • Adhesive Tape - consisting of virtually colorless, transparent, self-adhesive, pressure sensitive tape with adhesion strength of at least 190 N/m.

  • Hand lens capable of magnification x 10

 
PURPOSE: Dust on blast cleaned steel surfaces may reduce the adhesion of applied coatings and by absorbing moisture, may promote the corrosion of the blast cleaned steel.

 

PROCEDURE:
  • First discard the first three turns of tape from the roll.

  • Remove a piece about 8" long.

  • Touching the adhesive side only at the ends, press about 6" of freshly exposed tape firmly into surface to be tested.

  • Press by placing the thumb across one end of the tape and moving the thumb along the tape at a constant speed and pressure. Do this three times in each direction making each stroke take approximately 5 to 6 seconds.
    • NOTE: While a test procedure in which pressure is applied to a tape using the thumb is subjective, it is usually adequate, especially for use in situations where surfaces free from dust are required. In disputed cases, except when a rust grade C or D is involved, pressure may be applied to the back of the adhesive tape using a spring-loaded roller. Please refer to ISO F502.


  • Remove the tape from the test surface.

  • Display results on appropriate white board by rubbing with thumb to adhere.

  • Determine the QUANTITY OF DUST on the tape by comparing visually an area of the tape equal to an area of reference shown in FIGURE 1 below.

  • Determine the predominant DUST PARTICLE SIZE on the tape by referencing TABLE 1, which defines six dust particle size classes, designated 0, 1, 2, 3, 4 and 5.

  • Complete a significant number of tests to properly identify the characteristic of the surface tested. Complete at least three separate tests for each surface of a particular type of aspect. Complete at least two additional tests for each result that has a one or less quantity rating.
    • NOTE: Please refer to the ISO 8502-3 Standard for the exact procedure.
Figure 1 - Dust Quantity Ratings


 

Pictorial references corresponding to dust quantity ratings 1, 2, 3, 4 and 5.

NOTE: The use of intermediate half-steps is permissible if required to give a more detailed report.

Report any overall discoloration as quantity rating 5, size class 1.

 

TABLE 1 - Dust Size Classes
Class Description of dust particles
0 Particles not visible under X 10 magnification
1 Particles visible under X 10 magnification but not with normal or corrected vision (particles < 2 mils in diameter).
2 Particles just visible with normal or corrected vision (particles 2 mils to 40 mils in diameter)
3 Particles clearly visible with normal or corrected vision (particles up to 40 mils).
4 Particles between 40 mils to 100 mils
5 Particles larger than 100 mils

 

Spring Loaded Roller Apparatus

for Cleanliness Tape Test ISO 8502-3

as mentioned in Procedure 6.2b.

Spring Loaded Roller 11/30/05, Original Gardco design

Inquire About Special Web Pricing!

 

The CTR is made of selected materials that provide basically maintenance free service until components wear out. We do not recommend lubrication in any areas. This also will prevent contamination of the tape or test area from excess lubrication.The CTR external surfaces can be cleaned with a non-chlorinated solvent (Ensolv, etc.) or spray cleaner (409, Spray Nine, etc.). The CTR should not be immersed in a cleaner.

Available Items
Item Number Item
PA-980010 Cleanliness Adhesive Tape
MA-906171 Handheld Illuminated 10X Magnifier
PA-980003 Spring Loaded Roller Apparatus (CTR) - INQUIRE ABOUT SPECIAL WEB PRICING!

 

재성ITS tel:031-479-4211