ROTARY ABRASERS JSITS.com

세라믹이나 플레스틱,직물,메탈,가죽,고무,플로어링,페인트,라커칠또는

도금한 표면의 내구성을측정할때 사용합니다.

일체형의 견고한 디자인
싱글또는 듀얼 헤드 테스터
디지털 디스플레이
측정할 물질의 정확한 포인트를 0.5mm 단위로 쪼개어 측정해 마모에 취약한 부분을 표시해 줌.
테스트할 부분은 4.5평방인치로 재질의 모든방향에서 테스트할 표면을 완전한 원형으로 마모시키는
테스트가 진행됩니다,
나무껍질무늬의 에나멜 로 마감된 단단한 하우징부분은 제어판 막, LED디스플레이,컨트롤 및
인풋 키패드가 자리잡고 있습니다.

모델 5150-000은 두물질 혹은 한물질내에서 비교및 대비 테스트를 가능하게 해줍니다.

Taber Abraser Model 5150


INSTRUMENT SPECIFICATIONS

ANSI/SAE Z26. 1 Plastic
ASTM D 1044 Paints & Coatings
ASTM D 3884   Flooring
ASTM D 4060 Printing
ASTM D 5650Plastic
ASTM F 1478  Paper
5150

 

INSTRUMENT CHARACTERISTICS
In the hands of competent research technicians, Models 5130
and 5150 perform reproducible tests that are accurate to the variations of quality inherent in the testing material.

Both units are mounted inside a compact aluminum housing
finished in baked wrinkle enamel. The sturdy housing carries the control panel membrane with its various keys, digital
display for the LED readouts and key pad for operation. 		Taber Abraser Model 5130
5130

The Model 5150 Abraser is a dual unit which can test two different or identical materials separately or simultaneously for comparison and contrast. Because at this capability, many of its quality features are doubled.

Both models are covered by a 12 month warranty on parts and workmanship.

Model 5130 Dimensions:   Unit - 11" x 16" x 10" high - Net Weight - 80 lbs
Model 5150 Dimensions:   Unit - 20" x 14" x 10" high - Net Weight - 115 lbs

ABRASERs are durable, precision-built instruments designed as accelerated wear testers that test the wear resistance of a variety of specimens including solid materials, painted, lacquered, electroplated surfaces, plastic-coated materials, textiles, metals, leather, rubber and linoleum. Some of the materials whose wear properties are measured with ABRASERs include the following:

LuggageUpholsteryDental products
ClothingCarpetingPaper and paperboard
Ceramic tileGlassPlastic coatings
Decorative laminatesCoated MetalsPaint, lacquer & varnish
Resilient flooring PlasticsTextiles
RugsTraffic paint Anodic coating
WaxesElectronics Decorative sheets
Labels  

Materials to be tested are subjected to wear action of two abrasive wheels at a known pressure in grams. This wear action results when a pair of abrasive wheels is rotated in opposite directions by a turntable on which the specimen material is mounted. The abrading wheels travel on the material about a horizontal axis displaced tangentially from the axis of the test material which results in a sliding action.

An exclusive feature of the ABRASERs is a patented "X" pattern of abrasion, produced by the rotary rub-wear action of the wheels. The wear pattern formed is that of two intersecting areas or a slightly curved herringbone configuration from the outside to the center, and from the center to the outside of the specimen. An area of 30 square centimeters or over 4.5 square inches is subjected to test and a complete circle on the material surface is abraded at all angles of grain or weave.

ABRASION TESTING TEST CONTROLS

Rigid controls are exercised over the test by 1) electrically counting the revolutions of the turntable carrying the test specimen, 2) carefully selecting the abrasive quality of the abrading wheels, 3) recording the weight load in grams placed on the wheels and 4) removing abrased particles with a vacuum pickup.

QUIET CABINET

In some laboratory environments, the ABRASER and its associated vacuum system can create sound levels that are above normal. The new "Quiet Cabinet" will reduce sound levels and provide a convenient, dust-free work space.

Taber Quiet Cabinet

Features

Dimensions & Weight

Top half - 30" wide x 24" deep x 19.5" high, 75 lbs
Bottom half - 30" wide x 24" deep x 33.5 high, 130 lbs


TABER ABRADING WHEELS  

Taber Abrading Wheels are available in five levels of abrasiveness to suit a wide range of material testing applications. Wool felt or plain rubber wheels test delicate materials or the abrasiveness of materials such as dental powders. Wheels that feature abrasive particles in a resilient matrix of rubber or a hard matrix of vitrified clay are suitable for stiffer materials.

SELECTING ABRADING WHEELS  

The choice of abrading wheels for Models 5130 and 5150 should be based upon the wear the specimen material will be subjected to in actual use.

Abrading wheels for ABRASERs include five general types of varying abrasive quality:

The plain neoprene rubber wheel containing no abrasive grain is used for testing dental cleaning powders, dentifrice and for mounting sandpaper strips which are used as resilient wheels. These sandpaper strips must be changed after each 500 cycles of operation. The wool felt wheel is valuable in testing the wearing qualities of two fabrics in friction with one another.

NOTE: The CS-10F Resilient Calibrase Wheel is subject to deterioration especially in high ozone atmospheres. The CS-10F Calibrase Wheel should be used before the expiration date printed on the wheel.

Non-Resilient (Calibrade) Wheels are more easily subject to "clogging" and "crowning" and will require more frequent refacing with the Model 200 Wheel Refacer. Wheels may be refaced as often as required down to the minimum usable diameter of 1 -3/4" as indicated on the wheel label.

Under ordinary conditions, a load and wheel combination should run a minimum of 300 cycles on a material specimen before the end point occurs, otherwise the test is too harsh and does not correspond to normal wear.



ABRADING WHEELS SELECTION CHART

 
Item No. Type Composition Load Range
in Grams		 Abrasive
Action 		Servicing
Required
AB-CS -10 Resilient Rubber and
Abrasive Grain		 500 to 1000 Mild Refacing with S-11 disc
AB-CS-10F Resilient Rubber and
Abrasive Grain		 250 to 500 Very Mild Refacing with S-11 disc
AB-CS-17 Resilient Rubber and
Abrasive Grain		 500 to 1000 Harsh Refacing with S-11 disc
AB-H-10 Non-Resilient Vitrified 500 to 1000 Coarse Refacing with Model 200 Refacer
AB-H-18 Non-Resilient Vitrified 500 to 1000 Medium Coarse Refacing with Model 200 Refacer
AB-H-22 Non-Resilient Vitrified 500 to 1000 Very Coarse Refacing with Model 200 Refacer
AB-H-38 Non-Resilient Vitrified 250, 500, 1000 Very Fine, Hard Refacing with Model 200 Refacer & Multiple Point Tool
AB-CS-0 or
AB-S-32 		Resilient Non-Abrasive Rubber 250, 500, 1000 Very Mild No Refacing required
AB-S-42 Resilient Sand Paper Strips 500 to 1000 Medium No Refacing - Replace as needed
AB-CS-5 Resilient Wool Felt 250 to 500 None No Refacing Required.
AB-S-35 Non-Resilient Tungsten Carbide 500 to 1000 Severe Cutting
or Tearing Action		 Clean with Solvent
and Stiff Brush
 


TABER MULTIMEDIA ABRASER ATTACHMENT

5500 Multi-Media Attachment

FOR THE FIRST TIME EVER!

Measure the abrasiveness of fluids and powders.

The Multi-Media Abraser Attachment provides the first repeatable method for the evaluation of the abrasivity of fluids. The standard configuration consists of brass pins abrading on a steel wear disc mounted inside a rotating table with the medium as the abradent. The brass pins and steel disc can be tailored "in-house" to duplicate the materials in your specific application. Both R&D and quality control will benefit from the ability to re-create actual wear caused by fluids and powders on different substrates.

 
Item Number Item
AB-985500 5500 Multimedia Abraser Attachment (works with all ABRASERs)
 

 

ABRASER SPECIFICATION REFERENCE
 

AM Test Method #63DIN 53 754JIS K 6902NF T 54-351
ANSI/SAF Z26.1-1990DIN 53 799 JIS K 7204Pr En 13329:1998
AS 2001.2.28-1992DIN 68 861 T2Fed. Test MethodPR Env 175.333.08
AS/NZS 1580.403.2:1994DLAl: 1975 Std. #405 Method 1091 SAE J 365
ASTM C 501-84EN 438-2 1991Std. #191A Method 5306.1SAE J 948
ASTM C 1353.96Ford Lab. Test MethodStd. #191A Method 5309.2SAE J 1530
ASTM D 1044-94BN 108-02Std.#141 Method 6192SAE J 2394
ASTM D 3389-94Gen. Motors Test MethodMIL-A-8625FSIS 92 35 09
ASTM D 3884-92BN 108-04MIL-C-13495BTappi T 476 om-97
ASTM D 4060-95GM 9515MIL-I-43553B TT-C-542E
ASTM F 362-91GM 9911PMIL-M-13231CTT-E-487E
ASTM F 510-93GG-P-455BMIL-P 18493TT-P-85E
ASTM F 1478-95ISO 5470MIL-T-28800E TT-P-87D
BS 3900ISO 9352: 1995 NAS 1192TT-P-91D
Chrysler MS-PP11-1ISO 3537 NEMA LD3-3.1.3TT-P-95C
Chrysler MS-PP11-2ISO 4586-2: 1997 NF B 51-282 UNE 57-095-78
CNS K6591 ISO 7784-2: 1997 NF G 37-121 
DIN 52 347JISA 1453NF T 3O-015 
DIN 53 109   

ABRASER - AVAILABLE ITEMS
 
Item Number Item
AB-5130 ABRASER Model 5130 (Complete) 115V/60Hz
AB-5131 Same as above - 230V/50Hz Version
AB-5150 ABRASER Model 5150 (Complete) 115V/60Hz
AB-5151 Same as above - 230V/50Hz Version
Multimedia Packages
AB-985530 5130 Single 115V Abraser w/5500 Multimedia Attachment
AB-985531 5130 Single 230V Abraser w/5500 Multimedia Attachment
AB-985550 5150 Single 115V Abraser w/ one 5500 Attachment
AB-985551 5151 Single 230V Abraser w/ one 5500 Attachment
 

Abraser Furnished Complete with the following items:     

 
Item Description5130 Quantity5150 Quantity
    
AB-503-0023 Auxiliary Weights (1000 Gram Load) 2 4 (2 sets)
AB-503-0022 Auxiliary Weights (500 Gram Load) 2 4 (2 sets)
AB-E100-125 Specimen Holder, 4-1/4" O.D. 1 2
AB-E100-101 Hold-Down Ring for Specimen Holder 1 2
AB-100-237 Hex Wrench tor Hold-Down Ring 1 1
AS-S-11 Abrasive Discs br Retacing Calibrase® Wheels
(100/pkg)		 1 pkg 1 pkg
AB-S-12 Long-Handled Hand Brush 1 1
AB-S-16 Specimen Plates, 4" sq., (10/pkg.) 1 pkg 1 pkg
AB-CS-10 Calibrase® Wheels 2 2
AB-H-18 Calibrade® Wheels 2 2
AB-5130-70 Vacuum Unit with Clean-up Brush and Suction Hose 120v 1 1
AB-5130-70/02 Cleanup Brush 1 1
AB-5130-70/03 Suction Hose 1 1
Instruction Manual Instruction Manual 1 1
    

QUIET CABINET - AVAILABLE ITEMS

 
Item Number Item
AG- 128370 Quiet Cabinet - Top Half
AB- 128371 Quiet Cabinet - Bottom Half
AB-128372 Quiet Cabinet - Complete set
Write or call for brochure which describes test preparation, abrading wheels, selection chart, accessories and supplies, standards and specifications and complete price list